Honeycomb aluminum plate roller peeling testing machine

Honeycomb aluminum plate roller peel testing machine[Performance characteristics]
1. Automatic clearing: When the computer receives the test start instruction, the measurement system will automatically clear;

2. Automatic return: Automatic recognition test * strong force, the movable beam automatically returns to the original position at high speed;

3. Automatic archiving: Test data and experimental conditions are automatically saved to prevent data loss caused by sudden power failure and forgetting to save;

4. Test process: The test process, measurement, display, analysis, etc. are all completed by a microcomputer;

5. Display mode: Data and curves are dynamically displayed along with the test process;

6. Result reproduction: The test results can be accessed at will, and the data curve can be re-analyzed;

7. Curve traversal: After the test is completed, you can use the mouse to find the force values and deformation data point by point on the test curve, which is convenient and practical for obtaining test data of various materials;

8. Comparison of results: Multiple test characteristic curves can be superimposed, reproduced, amplified, and presented in different colors to analyze and compare a group of samples;

9. Curve selection: Stress-strain, force-time, strength-time and other curves can be selected for display and printing as needed;

10. Batch test: After setting the test with the same parameters once, the test of a batch of samples can be completed in sequence;

11. Test report: (standard format)

Tensile: * force, tensile strength, elongation at break, elastic modulus;

Compression: * Strength, compressive strength, yield strength, elastic modulus, test reports can also be programmed and printed in the format required by the user;

12. Limit protection: It has two levels of program control and mechanical protection;

13. Overload protection: Automatically stops when the load exceeds 10% of the rated value;

Emergency stop: There is an emergency stop switch, which is used to cut off the power supply of the whole machine in emergency;

Automatic diagnosis: The system has automatic diagnosis function, which regularly checks the measurement system and drive system for overvoltage, overcurrent, overtemperature, etc., and stops immediately in case of abnormal conditions;

14. Realize independent operation of host computer and microcomputer;

XJ 828CHoneycomb Aluminum Plate Roller Peel Testing Machine[Instrument Performance and Main Technical Parameters]
1. Specification and model:XJ 828C ;

2. * Large test load: 1000N, 2000N, 5000, 10000N, 20000N;
3. Force measurement accuracy level: Level 1;
4. Effective force measuring range: 10000N (* 0.4% of large load-***);
5. Force measurement accuracy: within 1% of the indicated value±;
6. Test force resolution: * 1/500000 of the large test force± (internal and external are not graded, and the resolution remains unchanged throughout the process);
7. Test speed adjustment range: 0.1-500mm/min (stepless speed regulation);
8. Speed accuracy: within 1% of the indicated value±;
9. Deformation measurement range: 0.4%—***FS;
10. Deformation accuracy: within 1% of the indicated value±;
11. Deformation resolution: * 1/500,000 of large deformation
  (The resolution remains unchanged throughout the entire process);
12. Displacement accuracy: within 1% of the indicated value±;
13. Safety device: electronic limit protection;
14. Overload protection: automatic protection exceeding 10% of the maximum load;
15. Effective test stroke: 700mm;
16. Effective test width: 340mm;
17. Host exterior size (length, width× and× height):
     590×380×1600（mm）;
18. Power supply motor: single-phase AC 220V± 10%, 400W;
19. Host weight: 150kg;

Basic configurationof XJ 828Choneycomb aluminum plate roller peel tester:

1. 1 test machine host

2. Two high-precision ball-type screws
3. 1 set of Dongneng servo motor and system

4. 1 high-precision sensor

5. A set of high-precision synchronization system from Taiwan Xiangjie Measurement Center

6. 1 set of material testing machine measurement and control system

7. 1 HP computer (optional)
8. 1 HP printer (optional)
9. 1 set of material testing machine test software (optional)
10. 1 electronic extensometer (optional)

11. 1 set of large deformation measurement system (optional)
12. 1 set of stripping fixture (optional)

In addition to the stretching and other fixtures listed above, there are also fixtures for stretching, compressing, bending, shearing, peeling, tearing, etc. of various materials such as sheets, belts, wires, foils, strips, fibers, plates, rods, blocks, ropes, cloth, nets, etc., which are interchangeable and users can purchase according to their own needs.

XJ 828Choneycomb aluminum plate roller peel testermeets the standards:
"HB 5443-90" and the national standard aluminum-plastic composite panels for building curtain walls,"GB/T 1453 -2005" flat compression performance test method for sandwich structures or cores,"GB/T 1455-2005" sandwich structures or cores Shear performance test method,"GB/T 1457-2005" sandwich structure roller peel strength test method and other requirements.